Old Masters Stain

Old Masters Weathered Wood Gel Stain Pint 82008

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Spanish Oak Wiping Stain Quart 12201

Old Masters Satin Poly-Urethane Interior Oil Based Topcoat 49504 by Old Masters

Sheen: Semi-Gloss

Size: Quart

Old Masters Interior Oil‐Based Polyurethane is a self‐leveling, clear finish designed to protect the beauty of interior surfaces. Easy application and quick drying, this polyurethane will provide lasting, durable protection from abrasion, marring, chipping, alcohol and water. Great for use on interior wood surfaces such as floors, bars, counters, tabletops, cabinets, wood paneling and doors.

Old Masters Satin Poly-Urethane Interior Oil Based Topcoat 49604 by Old Masters

Sheen: Satin 

Size: Quart

Old Masters Interior Oil‐Based Polyurethane is a self‐leveling, clear finish designed to protect the beauty of interior surfaces. Easy application and quick drying, this polyurethane will provide lasting, durable protection from abrasion, marring, chipping, alcohol and water. Great for use on interior wood surfaces such as floors, bars, counters, tabletops, cabinets, wood paneling and doors.

Old Masters Gloss Poly-Urethane Interior Oil Based Topcoat 49404 by Old Masters

Sheen: Gloss 

Size: Quart

Old Masters Interior Oil‐Based Polyurethane is a self‐leveling, clear finish designed to protect the beauty of interior surfaces. Easy application and quick drying, this polyurethane will provide lasting, durable protection from abrasion, marring, chipping, alcohol and water. Great for use on interior wood surfaces such as floors, bars, counters, tabletops, cabinets, wood paneling and doors.

Old Masters Fast Dry Oil Based Stain

Pickling White 61404

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Golden Oak 60204

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

American Walnut 61804

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Spanish Oak 61204

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Espresso  62304

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Dark Walnut 61004

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Early American 60704

Size: Quart

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Fast Dry Oil Based Stain

Size: Quart

Natural Tint Base 60104

Designed for craftsmen, this fast drying, high quality interior oil-based stain applies easily and enhances the wood’s natural grain with its intensified depth of color and clarity.

Fast Dry Stain is recommended for use on interior wood surfaces or surfaces on which the previous finish has been removed. This stain is preferred for hardwoods, such as oak, ash, walnut, and mahogany.

Where to Use
Experience optimal results on all interior wood surfaces, such as cabinets, doors, floors, furniture, and woodwork.

Surface Preparation
The wood surface must be clean, dry, and free from dirt, wax, or grease. Sand the wood thoroughly - first with medium grit sandpaper, then progressing to a fine grit paper. Always sand in the direction of the wood grain. Sand smooth, then remove dust particles with a lint-free rag or a tack rag. If staining previously finished surfaces, first restore the surface to bare wood by completely removing the old finish, then follow the surface preparation directions listed above.

Application
Stir well before and during use. Stain may be brushed, sprayed, or wiped onto the surface. Before the stain dries, wipe off excess stain with a soft cloth. Allow stain to dry thoroughly before applying topcoat.

Technical Information

Mixing and Tinting:
Achieve custom colors by intermixing Fast Dry Wood Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon to any Fast Dry Wood Stain or by adding colorant to Natural/Tint Base Fast Dry Wood Stain. Natural/Tint Base Fast Dry Wood Stain may be used to lighten a Fast Dry Wood Stain color in any proportion or as a tint base to which colorant may be added for ultimate color selection. The amount of colorant added may affect performance and extend dry time.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time:
Oil-based finishes may be applied 30 minutes after wiping. Dry times may be extended due to humidity, low temperature, lack of air movement, excess stain application, or lack of penetration. Be sure surface is thoroughly dry before top coating. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.

Cleanup:
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat:
We recommend Old Masters clear finishes. However, Fast Dry Wood Stain can be top coated with virtually any finish, including professional finishes such as lacquers and conversion varnishes. Wait 24 hours before top coating with a water-based clear finish.

EPA VOC: 550 g/L (4.5 lbs/gal)

Actual VOC: 550 g/L (4.5 lbs/gal)

Old Masters Spar-Marine Varnish, Clear Finish Topcoat, Oil Based Outdoor topcoat, flexible finish to withstand water and weather, UV ray topcoat

This is a superior exterior coating formulated to produce a high quality, flexible finish to withstand water and weather. It also contains ultraviolet absorbers for advanced sun protection. Available in satin, semi-gloss and gloss sheens.

Where to Use
Spar-Marine Varnish is recommended for use on exterior wood, fiberglass, coated metal, or painted surfaces. It can be used on unfinished wood surfaces or previously finished surfaces. This finish can also be used over stained surfaces that have thoroughly dried.

Ideal for use on exterior surfaces, such as fences, railings, lawn furniture, doors, boats, and marine surfaces. For interior use on windowsills and door frames for added ultraviolet protection. DO NOT USE on wooden decks or steps, wood siding, log homes, or wood boats below the water line.

Surface Preparation
All surfaces must be clean, dry, and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected.

Bare Wood: Sand surface thoroughly with medium grit sandpaper and progress to fine grit sandpaper. Always sand in the direction of the wood grain. Remove dust with a tack rag.

Previously Finished Surfaces: Surface should be sanded to remove imperfections and gloss, using extra fine sandpaper (220 grit) and, sanding with the grain. Remove dust with a tack rag.

Stained Surfaces: Stain must be thoroughly dry before applying clear finish. Do not sand uncoated stained surface.

Note: If a sealer is desired, we recommend Old Masters Penetrating Sealer.

Application
Stir thoroughly before and during application. DO NOT SHAKE. Do not apply in direct sunlight or areas of extreme air movement.

Apply with pure bristle or polyester brush, flat pad, or spray.
Apply in full, even coats. Flow on with minimum brushing to achieve a glass-like finish.
Spar-Marine Varnish will dry to touch in 4 to 6 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended.
Sand lightly between coats with fine sandpaper (220 grit) to produce a finer finish and promote adhesion. If sandpaper gums up, allow more dry time. Remove sanding dust.
Reapply. For exterior surfaces, a minimum of three coats should be applied.
Maintenance
As with all exterior clear finishes, this product will not offer unlimited protection against the elements. Surfaces which receive direct sunlight may have to be re-coated annually to maintain gloss and to prevent cracking and peeling.

Thinning
Do not thin. Use as packaged.

Coverage
Approximately 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time
Apply when air and surface temperatures are between 60° and 90°F and humidity is between 30% and 70%. At 50% relative humidity and 70°F, Spar-Marine Varnish will dry to touch in 6 to 8 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Drying time will be affected by temperature, humidity, and film thickness. Protect product from freezing prior to and during application.

Wait 24 hours before subjecting surfaces to light use. Care should be used during the first week after application as the finish is curing to its ultimate hardness.

Cleanup
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup.  The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.
MAX VOC: 350 grams/liter (2.9 lbs/gal)

Old Masters Spar-Marine Varnish, Clear Finish Topcoat, Oil Based Outdoor topcoat, flexible finish to withstand water and weather, UV ray topcoat

This is a superior exterior coating formulated to produce a high quality, flexible finish to withstand water and weather. It also contains ultraviolet absorbers for advanced sun protection. Available in satin, semi-gloss and gloss sheens.

Where to Use
Spar-Marine Varnish is recommended for use on exterior wood, fiberglass, coated metal, or painted surfaces. It can be used on unfinished wood surfaces or previously finished surfaces. This finish can also be used over stained surfaces that have thoroughly dried.

Ideal for use on exterior surfaces, such as fences, railings, lawn furniture, doors, boats, and marine surfaces. For interior use on windowsills and door frames for added ultraviolet protection. DO NOT USE on wooden decks or steps, wood siding, log homes, or wood boats below the water line.

Surface Preparation
All surfaces must be clean, dry, and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected.

Bare Wood: Sand surface thoroughly with medium grit sandpaper and progress to fine grit sandpaper. Always sand in the direction of the wood grain. Remove dust with a tack rag.

Previously Finished Surfaces: Surface should be sanded to remove imperfections and gloss, using extra fine sandpaper (220 grit) and, sanding with the grain. Remove dust with a tack rag.

Stained Surfaces: Stain must be thoroughly dry before applying clear finish. Do not sand uncoated stained surface.

Note: If a sealer is desired, we recommend Old Masters Penetrating Sealer.

Application
Stir thoroughly before and during application. DO NOT SHAKE. Do not apply in direct sunlight or areas of extreme air movement.

Apply with pure bristle or polyester brush, flat pad, or spray.
Apply in full, even coats. Flow on with minimum brushing to achieve a glass-like finish.
Spar-Marine Varnish will dry to touch in 4 to 6 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended.
Sand lightly between coats with fine sandpaper (220 grit) to produce a finer finish and promote adhesion. If sandpaper gums up, allow more dry time. Remove sanding dust.
Reapply. For exterior surfaces, a minimum of three coats should be applied.
Maintenance
As with all exterior clear finishes, this product will not offer unlimited protection against the elements. Surfaces which receive direct sunlight may have to be re-coated annually to maintain gloss and to prevent cracking and peeling.

Thinning
Do not thin. Use as packaged.

Coverage
Approximately 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time
Apply when air and surface temperatures are between 60° and 90°F and humidity is between 30% and 70%. At 50% relative humidity and 70°F, Spar-Marine Varnish will dry to touch in 6 to 8 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Drying time will be affected by temperature, humidity, and film thickness. Protect product from freezing prior to and during application.

Wait 24 hours before subjecting surfaces to light use. Care should be used during the first week after application as the finish is curing to its ultimate hardness.

Cleanup
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup.  The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.
MAX VOC: 350 grams/liter (2.9 lbs/gal)

Old Masters Rich Mahogany Wiping Stain Quart 15004

Old Masters Red Mahogany Wiping Stain Quart 11404

Old Masters Red Mahogany Gel Stain Pint 80408

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Pickling White Wiping Stain Quart 12404

Old Masters Pecan Wiping Stain Quart 12904

Old Masters Natural Wood Stain Quart 76104

Free of pigment, Natural allows wood to embrace its roots. Simple and pure, this tone highlights a wood's true beauty by gracefully brightening woodgrain. On oak, Natural emboldens the wood's red undertones. A versatile design element, this color can be used in combination with many other shades of stain to create an array of decorating styles. Clean and humble, Natural enhances any color palette or wood species with ease.

32oz quart

Old Masters Natural Wiping Stain Quart 11116

Old Masters Natural Tint Base Gel Stain Pint 80108

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Espresso Wiping Stain Quart 15204

Old Masters Espresso Gel Stain Quart 84404

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Espresso Gel Stain Pint 84408

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Early American Gel Stain Pint 80608

Why Stain?

Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:

-Add rich color and depth to a variety of surfaces, including wood, fiberglass, metal, and composition surfaces.
-Change existing colors on previously finished surfaces
-Match color tone on different kinds of woods and non-porous surfaces, such as fiberglass.

Where to Use

Gel Stain is specifically formulated for use on nonporous surfaces such as fiberglass, primed metal, and composition surfaces and is also suitable for wood applications. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Excellent for vertical surfaces. For outdoor use when topcoated with a protective exterior clear finish.

Surface Preparation

All surfaces must be clean, dry and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application

Stain application varies based on surface material. Please see application instructions below.

Application on Bare Wood: Apply stain liberally with brush or soft rag and remove excess, wiping in the direction of the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a rag dampened with paint thinner before stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while the stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces: To create a simulated wood look, apply stain to painted surface with foam or bristle brush or cheesecloth using long, smooth strokes. Realistic woodgrain patterns can be created by using the Old Masters Wood Graining Tool, as illustrated in the Old Masters Wood Graining Booklet.

Application over Previously Finished Surfaces: Scuff sand surface before application. Remove dust. Apply a liberal coat of Gel Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

If applying stain exteriorly, top coating with an exterior clear finish is strongly recommended.

Mixing and Tinting

Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. To lighten Gel Stain, mix any proportion with Natural Gel Stain. Stir for uniform consistency. DO NOT THIN.

Tinting

Approximately 1,000 to 1,200 square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately 800 to 1,600 square feet per gallon. If the surface is porous, coverage is approximately 300 to 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood.

Drying Time

Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface. For additional color depth, a second coat of stain can be applied after 8 hours. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup

Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Recommended Finish Coat

We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Ascend Exterior® or Old Masters Spar-Marine Varnish. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 550 grams/liter (4.6 lbs/gal)

Old Masters Dark Walnut Wiping Stain Quart 11804